How to Install a Ghost Immobiliser

Ghost immobilisers are hidden security system that shields your car from hacking and key cloning. It stops the engine from starting until a PIN code has been entered. This could be as long as 20 characters.

This additional layer of security is not visible to thieves who are unlikely to expect it. Certain systems have an app which allows the owner to disarm their immobiliser in the event of forgetting their PIN code or to use the service/valet mode.

Connecting to the vehicle’s CAN bus

The Ghost 2 Immobiliser, a cutting edge security system, can be integrated directly into the ECU of your vehicle. autowatch ghost immobiliser cost offers a discrete barrier against thieves. It is extremely efficient and user-friendly. This makes it a valuable addition to your vehicle’s security arsenal. Like all anti-theft devices, it’s not foolproof, and requires regular maintenance in order to function effectively. Fortunately, this guide can assist you in getting the most value from the Ghost 2 Immobiliser.

CAN (Controller Area Network) is a reliable serial networking, allows microcontrollers communicate with each other over short distances. Central control units is not required. It is designed for multiplexing electrical wiring in vehicles to reduce copper usage and has a number of advantages, including low cost and ease of use.

The CAN protocol is utilized in a majority of modern vehicles to communicate with the engine management system, steering control module and air conditioning controls and more. It also carries sensor information, such as speed sensors, as well as other inputs, in order to control the various features of the car. The CAN bus is used to monitor these diverse components, and can prevent the car from starting if they are in danger of failure.

While the CAN bus can be utilized for a variety of reasons, it’s essential to know how it functions and how it’s secured. Using CAN bus can be a great way to enhance the features of your vehicle, but it’s also essential to safeguard it from threats like hackers and other hacker. Installing a firewall, and monitoring your CAN-bus using software is the best method to accomplish this.

Ghost2’s secluded control unit is hidden in the car’s wiring harness or dashboard, eliminating the possibility of a criminal physically tampering with it. It is also impossible to reset a PIN or an emergency code without access to the vehicle.

You can enable Transport Mode if you need to surrender your vehicle to valet parking, service or any other reason. This option disables the Ghost immobiliser’s ignition and keyfob functions and will only be activated when the car reaches 31 mph for 15 minutes.

How do you create a PIN code

The Ghost immobiliser is a powerful security device that shields your vehicle from theft. The cutting-edge technology uses a PIN code to shut down the engine and stop it from running without the proper code or an authorized fob or mobile device. The system’s discrete design makes it unnoticeable, and provides unparalleled security against theft. The system is TASSA certified and could save you substantial amounts on your car insurance.

During installation when you install the Ghost system goes into an learning mode that records the sequence of buttons pressed to generate your unique pin code. The installer will guide you through activating the system after the pin code has been created. Once activated by the system, the Ghost system will disable the motor that starts your vehicle until a valid PIN has been entered or the vehicle is switched to transport mode. This makes it extremely difficult for thieves to clone or hack into your vehicle’s start system.

It is easy to install it is easy to install a Ghost immobiliser, but you must follow the specific instructions provided in the user’s manual to ensure that it is operating properly. Basic hand tools will assist in making accurate connections, and a multimeter can aid in checking the electrical value. Insulation tape and heat shrink tubing are a great way to shield the wire from damage, while cable tie is essential to keep everything neat and secure. Also, make sure to check the system frequently to spot any issues or potential mistakes.

Once the installation has been completed after the installation is complete, you must conduct a final test of the system prior to turning on the ignition in your vehicle. Ghost immobilisers will arm themselves after 3 to 30 seconds depending on the model of your car. It also has an option for Service/Valet that allows you to temporarily disable the system while you are servicing your vehicle or parking valet.

Ideally, the immobiliser should be concealed in an inconspicuous location under the steering wheel or on the dashboard. Make use of a small piece of tape or paint on the CAN H and L wires to make them easier to find when testing. The CAN H and the L wires must also be connected to an electrical source that can provide a constant 12V. It is important to check the connections again after testing as incorrect identification of these wires may cause the system malfunction.

The system must be activated

A ghost immobiliser prevents your car from starting when you press a few buttons on the vehicle, typically on the steering wheel or the door panel, or the central console. The sequence is set by the user and can be changed at any time. Once the system is activated it is in no way able to be removed by thieves which makes it a great choice for anyone who wants to protect their vehicle from theft.

The system is designed to be undetectable, meaning it can’t be detected by modern diagnostics or code-grabbing technology. It does not emit radio frequencies, making it even more difficult for thieves identify.

If the device is found it will stop the engine from running. It will also sound an alarm to scare thieves away. The device can be used to track the location of the car, which can help police locate it when it is stolen.

Contact Car Specalist Customs for a quote or to discuss your options if you’re interested in a Ghost immobiliser. We are certified to install ghost immobilisers for your vehicle. We will ensure that it is hidden in a place that is hard to reach. We can also provide additional security measures like the wheel lock and kill switch to help keep your car safe from thieves.

Disarming the System

If you have a Ghost immobiliser that is fitted to your vehicle, it’s essential to know how to disable it. This will assist you in the event that you lock your keys inside the car or when your battery dies. The system utilizes a unique PIN code that only you know, which means the immobiliser won’t start your vehicle unless you enter this code. The simplest method to enter the code is to press a series of buttons on your dashboard or steering wheel. This is a simpler method than using the key fob, and it also keeps anyone from copying your remote.

In contrast to some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and integrates with your vehicle’s CAN bus network to operate. Its most distinctive feature is that it bypasses the engine, without affecting normal vehicle functions. This makes it difficult for thieves to use signal boosters or clone car keys. It does not emit radio frequency, so thieves are unable to detect it.

The Ghost system has the option of a Transport Mode that allows you to temporarily disable security for certain situations like transportation or service. This feature is great when you’re lending your vehicle to someone else, without sharing your PIN code, or if your vehicle requires to be protected even while you drive it. Press the service button five times over two seconds to enable Transport Mode. The Ghost system will confirm activation with five indication signals.

After you’re done, make sure to save the emergency code in a secure place away from your vehicle. Then, if you ever find yourself locked out of your vehicle, contact the technician or the company who installed the system and they will give you the code. If you are unable to get in touch with them, you can seek out an authorized dealer. However, this could involve verification procedures, and you could be charged for additional fees.

This system is not just useful, but it will also protect your vehicle from theft and lower the cost of insurance. Many insurance companies offer lower premiums or financial incentives to install this anti-theft system.